[keksik334]

tak a ted dalsi orisek 😀 je mozne aby poustel zaroven animaci kdyz je na obou pinech HIGH?
tehne stav dela to kdyz sepnu oba tak jednou pusti levej podruhe pravej pasek a tak se to strida 🙂

[keksik334]

jde o to ze mi to falesne spousti… tak ze budu muset dat asi odpor mezi zem a vstupni pin? uz ho tam mam nabastlenej a pak to funguje

[keksik334]

jo brzdovku uz tam mam 😀 ale zadne animace dalsi 😀
jinak zeptam se je mozny aby bral vstup pro sepni az treba nad dva volty?

[keksik334]

Super dekuju za rady a pomoc 😉
az bude vse hotovo dam video jak to slape 🙂 ale nebude to zitra 🙂

[keksik334]

k napajeni asi pouziju LM spinat je asi opravdu hloupost pouzit LM tak pouziju nejaky ten odpor jak jsem jeste nehledal 🙂 rozumim tomu asi jako vcelam (vubec) ale bavi me spekulovat 😀

[keksik334]

Uz to mam dekuji moc za pomoc 😉

[keksik334]

neni za co se omlouvat to ja se omlouvam ze tomu vuuubec ale vuuubec nerozumim

Arduino: 1.6.10 (Windows 7), Vývojová deska: „Arduino/Genuino Uno“

C:\Users\Jiri\Documents\Arduino\netblink\netblink.ino: In function ‚void colorWipe(byte, byte, byte, int, int)‘:

netblink:48: error: ‚setPixell_pasek‘ was not declared in this scope

setPixell_pasek(i, red, green, blue);

^

netblink:49: error: ‚showl_pasek‘ was not declared in this scope

showl_pasek();

^

netblink:56: error: ‚setPixelp_pasek‘ was not declared in this scope

setPixelp_pasek(i, red, green, blue);

^

netblink:57: error: ‚showp_pasek‘ was not declared in this scope

showp_pasek();

^

exit status 1
‚setPixell_pasek‘ was not declared in this scope

[keksik334]

Dostanu se k void loop

Arduino: 1.6.10 (Windows 7), Vývojová deska: „Arduino/Genuino Uno“

C:\Users\Jiri\Documents\Arduino\netblink\netblink.ino: In function ‚void loop()‘:

netblink:33: error: ‚colorWipe‘ was not declared in this scope

colorWipe(0xff,0xa2,0x00, 40, 1);

^

netblink:39: error: ‚colorWipe‘ was not declared in this scope

colorWipe(0xff,0xa2,0x00, 40, 0);

^

C:\Users\Jiri\Documents\Arduino\netblink\netblink.ino: At global scope:

netblink:46: error: expected ‚,‘ or ‚…‘ before ‚if‘

if(pasek == 0){

^

netblink:63: error: expected ‚)‘ before ‚}‘ token

}

^

netblink:63: error: expected initializer before ‚}‘ token

netblink:63: error: expected declaration before ‚}‘ token

exit status 1
‚colorWipe‘ was not declared in this scope

[keksik334]

dekuji za reakci.. mam doma 7805 muzu pouzit? budu brat signal primo od blinkru mam to nejlepe dostupne tak ze bych dal 7805 snizil napeti na 5v privedl na pin. jinak na stole super uz funguje sepne po propojeni pinu tak ze zaklad bych mel
a ted kdyz bych chtel spinat animaci na dvou vystupech (prava nebo leva strana)? 🙂

#include <Adafruit_NeoPixel.h>
#define PIN 6
#define NUM_LEDS 12
// Parameter 1 = number of pixels in strip
// Parameter 2 = pin number (most are valid)
// Parameter 3 = pixel type flags, add together as needed:
//   NEO_KHZ800  800 KHz bitstream (most NeoPixel products w/WS2812 LEDs)
//   NEO_KHZ400  400 KHz (classic 'v1' (not v2) FLORA pixels, WS2811 drivers)
//   NEO_GRB     Pixels are wired for GRB bitstream (most NeoPixel products)
//   NEO_RGB     Pixels are wired for RGB bitstream (v1 FLORA pixels, not v2)
Adafruit_NeoPixel strip = Adafruit_NeoPixel(NUM_LEDS, PIN, NEO_GRB + NEO_KHZ800);

void setup() {
  pinMode(8, INPUT);
  strip.begin();
  strip.show(); // Initialize all pixels to 'off'
}

void loop() {
    if(digitalRead(8))
    {
      colorWipe(0xff,0xa2,0x00, 40);
      colorWipe(0x00,0x00,0x00, 5);
    }
  
}

void colorWipe(byte red, byte green, byte blue, int SpeedDelay) {
  for(uint16_t i=0; i<NUM_LEDS; i++) {
      setPixel(i, red, green, blue);
      showStrip();
      delay(SpeedDelay);
  }
}
void showStrip() {
 #ifdef ADAFRUIT_NEOPIXEL_H 
   // NeoPixel
   strip.show();
 #endif
 #ifndef ADAFRUIT_NEOPIXEL_H
   // FastLED
   FastLED.show();
 #endif
}

void setPixel(int Pixel, byte red, byte green, byte blue) {
 #ifdef ADAFRUIT_NEOPIXEL_H 
   // NeoPixel
   strip.setPixelColor(Pixel, strip.Color(red, green, blue));
 #endif
 #ifndef ADAFRUIT_NEOPIXEL_H 
   // FastLED
   leds[Pixel].r = red;
   leds[Pixel].g = green;
   leds[Pixel].b = blue;
 #endif
}

void setAll(byte red, byte green, byte blue) {
  for(int i = 0; i < NUM_LEDS; i++ ) {
    setPixel(i, red, green, blue); 
  }
  showStrip();
}

[Autor]

Příspěvky